RIELLO nozzle bracket（3006420）

Riello nozzle bracket（3006420） It is mainly used to fix and support the nozzles of the burner to ensure that the nozzles are in the correct position in the burner to ensure that the injection effect of fuel or gas meets the combustion requirements. It is usually made of metal materials, has certain strength and high temperature resistance, and can adapt to the high-temperature working environment inside the burner. Functions: Fixed nozzle, positioning guide, support protection.

Krom schroder controller IFW 15-T

Krom schroder controller IFW 15-T The IFW 15-T is a device for flame monitoring and control, mainly suitable for burners using single-electrode ignition detection, and is commonly used in combustion control systems in industries such as petroleum, chemical, and natural gas. It features a high-strength heat-resistant plastic housing. The upper cover, which can be plugged and unplugged, contains the control circuit board, flame signal amplifier, and a green indicator light. The base mainly has terminal blocks, neutral wire bars, and ground wire bars, as well as two 5.5mm round holes for installation. Working voltage: 220/240V AC, -15/+10%, 50/60Hz, suitable for both grounded and ungrounded systems. Self-power: 12VA. Ionization electrode voltage: 230V AC. Flame ionization current: ≥1μA. Output signal: Two sets of passive contact switches, one normally open and one normally closed. Contact capacity: 2A. Environmental temperature: -20℃ to +60℃. Protection grade: IP40. Dimensions: 72mm × 82mm × 94mm. Weight: 370g. Main functions: Flame monitoring: Supports both ionization and UV ultraviolet flame monitoring methods. Through the built-in flame signal amplifier, the flame current signals detected by the electrode or UV sensor are converted into two sets of switch signals to indicate the presence or absence of flame. Control function: Enters standby mode after power-on. When a flame signal is received, the internal relay operates, and its relay switch can participate in various controls. It can be combined with a PLC to achieve various burner controller functions, and can control the operation or stop of the combustion system based on the flame status, ensuring the safety and stability of the combustion process. Status indication: Equipped with a flame detection panel signal light indication function, which can visually display the flame status, making it convenient for operators to understand the equipment operation in real time.

Krom schroder leak detector TC 410-1T (84765810)

Krom schroder leak detector TC 410-1T (84765810) TC 410-1T is a device used for detecting gas leaks, mainly for checking gas leaks in valve groups or two single valves before the burner is ignited or after it is extinguished to ensure the safety of the gas system. Power supply voltage: 220/240V AC, -15/+10%, 50/60Hz. Energy consumption: 10VA. Fuse: Fine wire fuse, slow-blow, type H as per IEC 127. Switching current of the valve / enabled output: 5A resistive load (UL listed: 5A at 120V), 2A at cos=0.35. Fault output: Dry contact (internal undamaged), 1A for 220/240V (high voltage: 264V), 2A at 120V. Test time: 10-60 seconds. Dimensions: 158mm × 120mm. Main functions: Gas leak detection: Can detect whether there is a gas leak in the valve group or two single valves before the burner is ignited or after it is extinguished, ensuring the safety of the gas system. Adjustable test time: The test time can be adjusted according to different test volumes by adjusting the leakage rate and inlet pressure, and an external pressure switch is required to set the pressure for coordination. Adapt to various system debugging: During the sequential test period, it can adapt to different system debugging, allowing for quick system startup. Safety certification: Passed EC type testing and certification, as well as FM and UL certifications, ensuring quality and safety.

Krom schroder BR 165RB burning head（74337857）

Krom schroder BR 165RB burning head（74337857） The BR 165RB burner head is a professional gas combustion equipment component, mainly used in industrial heating fields and can be used in conjunction with various gas burners. Its appearance may be cylindrical, with a specially designed head featuring gas injection holes and air mixing channels to ensure uniform mixing of gas and air for efficient combustion. It may be made of high-temperature and corrosion-resistant alloy materials, capable of stable operation in high-temperature environments and having a long service life. Fuel application range: The BR 165RB may also be suitable for common gas fuels such as natural gas and city gas. Rated thermal power: Its rated thermal power may range from 100 to 500kW. Gas pressure range: The applicable gas pressure range of the BR 165RB may be between 5 and 30kPa, ensuring normal operation under different gas supply conditions. Air flow demand: To ensure complete combustion, it is necessary to match an appropriate air flow. The expected air flow required by this burner head may be between 5 and 20m³/h, which is specifically related to the combustion power and fuel type. Outer dimensions: Its outer dimensions may be approximately 165mm in diameter (possibly related to the 165 in the model), and the length may vary according to the actual application scenario and installation requirements.

RIELLO F5 burning cylinder（3006071）

RIELLO F5 burning cylinder（3006071） Product code: 3006071 Category: Fuel burner accessories Appearance dimensions: Combustion tube length L = 207mm, extended length L1 = 365mm. Type of burner and application scope: Suitable for Riello RL series two-stage oil-fired burners. The output range of this series of burners is 154 - 2700kW, and they can be used in various low-temperature and medium-temperature hot water boilers, hot air and steam generators, and thermal oil furnaces. Functions: Fuel delivery and atomization, air supply and mixing, flame stabilization and control, heat transfer and output, safety protection.

RIELLO G3-G20 oil pipe （3005720）

RIELLO G3-G20 oil pipe （3005720） Product code: 3005720 Category: Burner accessories This model is suitable for burners such as G5, G10, G20, G20S. External dimension: length is 1000mm. Joint specifications: G1/4 inner wire at one end and G3/8 inner wire at the other end. Function: convey fuel, adapt and connect, and ensure combustion efficiency.

RIELLO G5-G10 electrical machinery 90W (3008451)

RIELLO G5-G10 electrical machinery 90W (3008451) Product code: 3008451 The G5-G10 is a motor specifically designed for Riello burners. It is suitable for Riello 40G5, 40G10 and other burner models, with a power of 90W. Purpose: It mainly serves as the power component of the burner, providing power support for the burner's related components. Functions: Drive the fan: It provides power to the burner's fan, enabling it to rotate and draw in outside air into the combustion system. This ensures there is sufficient combustion-supporting air during the combustion process, promoting complete fuel combustion, enhancing combustion efficiency, and also facilitating the expulsion of combustion-generated exhaust gases. Drive the oil pump: It can drive the fuel pump to operate, allowing fuel to be smoothly transported from the fuel tank to the fuel injector, ensuring a stable fuel supply and providing a continuous fuel source for combustion, maintaining the normal operation of the burner. Ensure stable system operation: With stable power output, it maintains the coordinated operation of all burner components, ensuring the stability and reliability of the burner's overall operation. Its rated power and speed design can meet the operational requirements of G5 - G10 burners under different working conditions, guaranteeing a continuous and stable combustion process and reducing faults caused by insufficient or unstable power.

RIELLO G20-GS20 wind leaves（3005799）

RIELLO G20-GS20 wind leaves（3005799） Applicable models: Suitable for burners such as G20, GS20, FS20 and other models of Liya Road. Brand and Model: The brand is RIELLO, the model corresponds to G20 - GS20, Product code: 3005799. Type: belongs to the motor wind wheel, generally centrifugal air blades, usually made of high-strength and heat-resistant materials to adapt to the working environment of the burner. Function: Provide combustion-assisted air, stabilize the combustion process, discharge exhaust gas, and reduce operating noise.

RIELLO P140-450TN distributor（3003707）

RIELLO P140-450TN distributor（3003707） Product number：3003707 Category: Burner accessories Appearance material: usually made of metal to adapt to the high temperature environment inside the burner. Functional characteristics: As a distributor, its main function is to evenly distribute fuel or combustion air to the combustion area to ensure that the fuel and air are fully mixed to achieve efficient and stable combustion. It may also have certain support and fixing functions to ensure the relative position of the internal components of the burner.

RIELLO P450 oil nozzle seat (3006172)

RIELLO P450 oil nozzle seat (3006172) Category: Burner accessories Usually made of high temperature and corrosion resistant metal materials to adapt to the high temperature fuel environment inside the burner. Its appearance has a specific cavity structure, with a mounting interface that matches the oil nozzle and an interface that connects to the fuel pipeline. It is used to accurately install the oil nozzle and connect to the fuel delivery pipeline. The product number is 3006172 and is specially used for burners of related models such as Riello P450. Functions: Fix the oil nozzle, connect the fuel pipeline, assist in fuel atomization, heat dissipation and protection.

RIELLO RL50 Oil pump AL75C 9411-4 (20033547)

RIELLO RL50 Oil pump AL75C 9411-4 (20033547) Product code:20033547 Generally, it can work within a certain pressure range and provide stable fuel flow in accordance with the fuel requirements of the RL50 burner. Combined with the power supply requirements of the RL50 burner, oil pumps are usually suitable for 380V, 50Hz three-phase power environments. Appearance and material: Usually made of metal, with good wear and corrosion resistance to adapt to fuel environment. The appearance is in the shape of a pump body, with oil inlet and oil outlet, which is used to connect the fuel pipeline. Functions: fuel delivery, pressure regulation, flow control, and ensure combustion stability.

RIELLO RL190 burning cylinder（3012561）

RIELLO RL190 burning cylinder（3012561） Product number：3012561 This burner is a double-section fire burner, mainly used in boilers and other equipment. Appearance structure: Usually a cylindrical structure, generally made of high temperature resistant metal materials, such as stainless steel, etc., which can withstand high temperatures during combustion. Its shape and size match the overall structure of the RL190 burner, making it easy to install at the connection between the burner and the boiler. Function: Form a combustion space, guide airflow and flame, resist high temperature and protection, and stabilize combustion.

RIELLO RLS28-50 liquefied gas head (3010304)

RIELLO RLS28-50 liquefied gas head (3010304) RLS28-50 ：It is an accessory for the RLS series burners in Riya Road, mainly used for combustion systems for liquefied gas fuels. Applicable models: Applicable to dual-fuel burners of RLS28, RLS50 and other models of Riello. These burners can be used for hot or superheated water, hot air generators or steam boilers, thermal oil furnaces and other equipment. Appearance material: Usually made of high temperature and corrosion resistant metal materials to adapt to the high temperature environment and gas characteristics of liquefied gas combustion. The appearance has a specific shape, generally has a gas inlet and a combustion outlet, and is equipped with an installation structure connected to the burner main body, which is convenient for precise installation. Functions: Introduce and distribute liquefied gas, promote gas atomization and mixing, stabilize flame, and adapt to burner adjustment mode.

RIELLO RLS50 Ignition rod（3013020）

RIELLO RLS50 Ignition rod（3013020） Product number：3013020 The burner adjustment method is "double-section fire", which is often used in hot water or superheated hot water boilers, hot air generators, steam boilers and other equipment. It is usually a slender rod-like structure, with one end being an ignition end and the other end being connected to the ignition cable. The material is generally high temperature resistant and has good electrical properties, such as stainless steel, to ensure stable operation in high temperature environments and not easy to be oxidized. Function: generate electric sparks, accurately position and ignite, and adapt to different working conditions.

RIELLO RLS70-130 liquefied gas head (3010305)

RIELLO RLS70-130 liquefied gas head (3010305) Product number：3010305 RLS70-130：It is an accessory for the RLS70-130 series oil and gas dual-purpose burners in Liya Road, mainly used for the combustion system of liquefied gas. Suitable for dual fuel burners of RIELLO RLS70, RLS100, RLS130 and other models. These burners can be used in hot or superheated water boilers, hot air generators, steam boilers and thermal oil furnaces and other equipment. It is usually made of corrosion-resistant and high temperature resistant metal materials to adapt to the high temperature and gas characteristics when liquefied gas is burned. Functions: gas delivery and distribution, promote gas mixing, adapt to combustion adjustment mode, and stabilize flame.